HT12D is a series decoder IC for remote control applications manufactured by Holtek. It is commonly used for radio frequency (RF) applications. Download. HT12D. 8. 4. L. Ö. RC oscillator. DIN active ²Hi². 18DIP, 20SOP. HT12F. 0 Holtek¢s series of encoders (refer to the encoder/de- . C o n tro l L o g ic The information appearing in this Data Sheet is believed to be accurate at the . HT12DDIP Ic-remote Control Decoder Features. Operating voltage: V~12V Low power and high noise immunity CMOS technology Low standby current.

Author: Nishura Moogumi
Country: Martinique
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 21 March 2005
Pages: 65
PDF File Size: 14.19 Mb
ePub File Size: 13.30 Mb
ISBN: 376-6-30517-910-5
Downloads: 25059
Price: Free* [*Free Regsitration Required]
Uploader: Gumi

We will notify you the result by email. If any valid data is received they can be obtained from these four pins. This oscillator can be used by connecting these two pins through a 1M Resistor. For decoding a data the IC will requires an oscillatorluckily this IC has one in-built. Choosing Battery for Robots.

HT12D Decoder IC

If you want security you can connect any of the 8 pins to 5V to make it high. HT12D is a decoder integrated circuit that belongs to 2 12 series of ht21d. This ICs are paired with each other. Photograph just for reference. The input data code is decoded when no error or unmatched codes are found.

SPI Module of Arduino. These two ICs together form an Encoder and Decoder pair. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be datwsheet suited for you.

To know how a hh12d data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here. Actual product may vary from the product photograph displayed above.

Related Articles  FR9024N PDF

A valid transmission in indicated by a high signal at VT pin. Supply voltage; 5V 2.

Submitted by admin on 27 October It is very important that your Decoder should have the same address of that of the encoder. TL — Programmable Reference Voltage.

Choosing Motor For Robots. The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7. This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This pin will go high when a data is received.

These are the 8-bit address bits, which is used to protect your data. Interface SD Card with Arduino. Dtasheet transmission; active high. In simple terms, HT12D converts the serial input into parallel outputs. What is Web Browser. They dfcoder paired with 2 12 series of encoders. Easy to Use, Datadheet Robotics Kits This series of decoders are mainly used for remote control system applications, ht12dd burglar alarm, car door controller, security system etc.

So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. The Encoded 12 bit output data obtained from HT12E has to be given here.

Interface GPS with Arduino. This high-density System-in-Package SiP integrates controller, power switches, and support components. It decodes the serial addresses and data received by, say, an RF receiver, decoded parallel data and sends them to output data pins. The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded.


TB Stepper Motor Driver 4. The Decoder receive the serial address and data from its corresponding decoder, transmitted by a carrier using an RF transmission medium and gives output to the output dwtasheet after processing the data.

The serial input data is compared with the local addresses three times continuously. It is not mandatory to use it.

HT12D Decoder IC | HT12D Datasheet | Pin Diagram

Customers who bought this product also purchased Full Name Email Address. Buy 15 or more pieces to get Free Shipping Option Availability: We should set the bits in same pattern on Encoder and Decoder IC to pair them.

We will lauch an immediate investigation and try our best to beat the price, if it proves to be the same product. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

It is mainly provided to interface RF and infrared circuits. They are capable of Encoding 12 bit of information which consists of N address bits and N data bits. Found this item with same quality and at a lower price but prefer to buy from robokits.

Easy Interface with and RF or an Infrared transmission medium. The IC has a built in oscillator. This pin powers the IC should use only 5V.

Be the first to write a review. Skip to main content. The data on 4 bit latch type output pins remain unchanged until new is received.